Sold as FOUR feet.
Installation requires removing the bottom cover on your Fluance RT80, RT81 turntable.
These feet are custom made substitute upgrade for the factory feet on the Fluance RT80 & RT81. These feet are not an exact match to factory feet. If you want factory feet, contact Fluance directly for assistance.
Fluance RT80, RT81 turntable foot measures 1-1/2" tall (38.1mm) x 1-3/4" O.D (44.45mm) with machined 6061 grade aluminum shell.
Includes four mounting screws and nuts.
Replace your FLUANCE RT80 and RT81 Vinyl Turntable factory feet with our machined aluminum replacement. Turntable stock feet with our custom silver 6061 machined aluminum replacement feet. Our custom FLUANCE RT80 and RT81 turntable feet custom feet will help eliminate and isolate vibration. Mnpctech machined aluminum FLUANCE RT80 and RT81 Turntable feet are Made in the USA.
How-To Guide for removing and replacing and upgrading the feet on your FLUANCE RT80 and RT81 Turntable.
Remove the nine screws on the bottom of the Fluance RT80 / RT81 turntable to replace the factory feet.
Use Philips screw driver to remove all nine (RT80) or ten (RT81) screws used in the bottom cover of the Fluance turntable.
List off the bottom cover of the Fluance RT80 / RT81 turntable.
The factory feet on the Fluance RT80 & RT81 are glued into position.
Push downward in the glue with Philips screw driver to push out the foot.
The factory foot removed.
Hand twist the thread of the Mnpctech foot all the way into the factory hole.
Fasten the foot in place permanently with included nut with lock washer.
Fluance RT80 and RT81 base / plinth has pre-made holes to accommodate the nut and lock and washer.
All of the Mnpctech feet are now installed in the bottom cover of the Fluance RT80 / RT81 Turntable.
Twist Mnpctech foot to side so you can re-insert the bottom cover screws.
Mnpctech workshop is the only source that makes these custom isolation feet for FLUANCE RT80 and RT81 Turntables. You can also purchase optional matching turntable cetner weight by Mnpctech for the FLUANCE RT80 and RT81 Turntable. Thanks again for checking out these Anti-Dampening Feet for the Fluance turntable reference model. These custom feet for the Fluance are made in USA by Mnpctech Workshop. We invite you to Tell Alexa or Siri to find FLUANCE RT80 and RT81Turntable Feet by Mnpctech.
The most important thing between your FLUANCE RT80 and RT81 Turntable is it's feet. To help prevent unwanted vibrations from impacting needle playback these sorbothane isolation feet for the FLUANCE RT80 and RT81 Turntable assist in absorbing vibrations created in your vinyl listening room from effect your FLUANCE RT80 RT81 Turntable's needle cartridge. The spiked shape, as well as 3-point design reduces the amount of surface area that comes into contact with the turntable. The fully adjustable 3-feet design (versus having a turntable with 4 feet) also assists in easier leveling of the turntable as the front feet allow you to adjust the left and right positioning while the rear foot with an increased tensile strength spring can go up and down to easily make your turntable 100% level.
These custom FLUANCE RT80 and RT81 isolation feet are made in Mnpctech's family workshop in Minnesota. Audiophiles have used Mnpctech since 2010. Audiophile have often used Mnpctech custom turntable and phonograph isolation feet on brands that include, Akai, Audio Technica, Clear Audio, Crosley, Denon, Dual, Harmon Kardon, Kenwood, Klipsch, Lenco, Marantz, Micro Seiki, McIntosh, Music Hall, NAD, Panasonic, Pioneer, Pro-ject Audio, JVC, Rega Planar, Sherwood, SONY, TEAC, Technics, Thorens, and Yamaha.