Replacement C-Clip, 4 Pack for Scythe Gentle Typhoon Fan

Replacement C-Clip, 4 Pack for Scythe Gentle Typhoon Fan


 

$2.99

22 item(s)
+

4 Pack for Replacing damaged or lost Scythe Gentle Typhoon Fan C-Clip Retaining Ring.

Here are the PC Cooling fans we've confirmed uses this type of metal retaining ring or c-clip. Please email us other fan models we can add to this list.

Nidec-Servo Scythe Gentle Typhoon

Darkside Black Edition (D122C)

ADDA AD1212LB-A73GL

Delta WFB1212H







Guide to Removing and Installing Scythe Gentle Typhoon Fan C-Clip Retaining Ring.


DIY Guide to Removing & Installing PC Cooling Fan External Retaining Ring with Mnpctech C-Clip Pliers.

The Nidec-Servo's Scythe Gentle Typhoon (Model# D122C). This fan has been regarded as the best static pressure optimized fan by DIY PC community since it's release in 2008. The original D122C is no longer made, but there is limited stock available at some online retailers. Last year the D122C Scythe GT fan was resurrected and manufactured as "Darkside Black Edition" by Dazmode. It's the same specs as the original, but now has Black fan blades. Many PC Modders including myself have painted these fans to fit the color schemes of our custom PC builds. I've been asked several times over the years how to remove the metal c-clip without losing or breaking it?*This is my DIY guide to removing and installing external retaining ring or c-clip. Like many others, I've also lost these tiny c-clips while learning the best technique for handling this task.

Nidec-Servo's Scythe Gentle Typhoon Factory Spec PDF link, [url=http://www.nidec-servo.com/en/digital/pdf/D1225C.p...">http://www.nidec-servo.com/en/digital/pdf/D1225C.p....]http://www.nidec-servo.com/en/digital/pdf/D1225C.p...*[/url]

Speed: *2150RPM

Air performance : 68.8CFM

Nose: 34db (25cm from the fan, free air)

Power: 12VDC, 0.123A (0.63A peak max)

Operational voltage range: 5-12V (~900rpm-2150rpm)

Bearing: Ball

Expected life: 100000h/35c or 55000h/60c

Appearance: Full black

Dimensions: *119 x 119 x 25 mm / 4.68 x 4.68 x 0.98 in

WARNING:

Perform this task with Safety Glasses, the tiny Black metal retaining ring (c-clip) can and likely will pop off, so perform this task in a clean workspace, so you can find it. I suggest doing the work on a large white bed sheet and holding a large magnet near the fan hub as you remove and re-install the c-clip, to increase you're chances of not losing the c-clip. I haven't found a source for ordering replacement c-clips yet, but I'm still searching.



Here is my suggested Tools & Supplies

Safety Glasses (not pictured)

Heat Gun for removing the fan label. Hair Dryer on HIGH setting will work as well.

10" Wire Cable Tie

Large magnet (not pictured)

Mnpctech External Fixed-Tip Retaining Ring Pliers

Tweezers

Needle Nose Pliers

Super Glue (not pictured)


The fan blade looks as if it would snap-on and off, but not the case.


We need to remove the back label to access the external metal c-clip on the fan shaft.


Swipe heat gun or hair dryer back and forth over the label.


Use the Tweezer to peel off the fan label.


Stick the fan label on a clean metal surface while you perform your work.


You will tie down the fan hub with this Twisty tie. The fan shaft has a retention spring inside. You need to compress this spring, so you can remove the metal c-clip. If you don't, it's almost a guarantee that the c-clip will fly off the shaft faster than a bullet.


Using Twisty tie to compress the fan hub spring, by tying down the hub to the fan frame.



Close ups of the Black metal c-clip inside the Nidec-Servo Scythe Gentle Typhoon.



Insert the two prongs of the Retaining Ring Plier inside the jaw of the c-clip.


If you have a large Magnet, Position it near the fan hub, just in case the c-clip pops off.



Holding the black metal c-clip in the Retaining Ring Plier


You will widen the jaw of the c-clip while removing it. You need to bend it back to it's original opening, so it maintains it's grip.


Hold the c-clip in the Tweezer while using a Needle Nose Plier to compress jaw of the c-clip.


Doing this will allow you to re-use the metal c-clip.


If you're wanting to paint your PC cooling fan. You can watch this video guide by Mnpctech


View of the spring inside the Gentle Typhoon PC Cooling fan, "Be careful, don't lose it!"


To re-install the metal fan c-clip, grip the c-clip in reverse position on the Plier.


Reversing the c-clip on the plier will make it easier to re-install the metal cooling fan c-clip


Reversing the c-clip in the Plier will make it easier to re-install the metal cooling fan c-clip.


If the cooling fan label has very little adhesion left, I'll apply drops of Krazy or Super Glue to re-apply the label.


The job is finished!



Enter name, address, and email below for your chance to win the MNPCTECH CARBON FIBER GPU SUPPORT BRACKET. One Random Winner will be emailed Tracking on 9/22/17. OPEN TO ALL COUNTRIES!!

9/13/17: Included screws updated to black 6/32 pan head machine screws with washers.

To celebrate the success of our custom GPU Support arm brackets, Mnpctech has created an limited edition 100% real carbon fiber GPU support bracket. Carbon Fiber allows us to make a design that is very sleek and simple without concern about the structural support strength.

This GPU support bracket works with all manufacturer video card models including reference, non-reference and video cards with GPU water blocks.

Mnpctech "Limited-Edition" Carbon Fiber GPU support bracket includes:

1x 100% Carbon Fiber bracket with angle slots for height adjustment of the bumper cushion.

2x Black anodized stainless steel 6/32 thread flat head PCI slot mounting screws.

1x Black anodized machined aluminum adjustable pedestal with Black rubber cushion with two 6/32 screws pre-installed.









 

Type the characters you see in the picture above.